Author Topic: new CZ family member. but 1 question  (Read 426 times)

0 Members and 1 Guest are viewing this topic.

Offline puddintame

  • Sr. Member
  • ****
  • Posts: 492
new CZ family member. but 1 question
« on: July 03, 2017, 01:44:04 AM »
http://imgur.com/a/de0fU friggin image wont upload. anyway new to me but a used phantom in mint cond. along side my other two cz's pert sweet. my question is that some mags drop free, and some don't. gotta pull the latter ones out. the phantom didn't come with fact. mags. I have 6/16rnd mags and half drop free. no issue. the others I have to pull out.

« Last Edit: July 03, 2017, 01:54:31 AM by puddintame »

Offline WVNed

  • Newbie
  • *
  • Posts: 29
Re: new CZ family member. but 1 question
« Reply #1 on: July 03, 2017, 08:26:50 AM »
test
OPs pic
WHAHOOOoooooooooo

Offline Tok36

  • Hero Member
  • *****
  • Posts: 3473
Re: new CZ family member. but 1 question
« Reply #2 on: July 03, 2017, 11:56:05 AM »
Just a heads up, you need to use the BBCode (message boards & forums) that Imgur provides when posting in forums like this.

On another note, gratz on the Phantom, i would take a look at the mag break and see if it is tweaked. This could effect the mag dropping. Edit: See reply#5, Phantom dose not have a mag break.
« Last Edit: July 03, 2017, 03:03:13 PM by Tok36 »
Will work for CZ pics! (including but not limited to all CZ clones)

Offline armoredman

  • Administrator
  • Hero Member
  • *****
  • Posts: 16781
Re: new CZ family member. but 1 question
« Reply #3 on: July 03, 2017, 12:41:09 PM »
Another thing is are the magazines CZ factory? I have had difficulty with aftermarket mags in my Phantom, as the specs are not 100% the same as the SP01.

Offline puddintame

  • Sr. Member
  • ****
  • Posts: 492
Re: new CZ family member. but 1 question
« Reply #4 on: July 03, 2017, 02:09:00 PM »
thanks for the tips fellas. the phantom came with 16rnd mags and I cant tell if they are factory or mecgar. ill take a closer look and report back

Offline cntrydawwwg

  • Hero Member
  • *****
  • Posts: 4214
Re: new CZ family member. but 1 question
« Reply #5 on: July 03, 2017, 02:29:52 PM »
No mag break on the Phantom.
   PT, I had a couple Mecgars stick a little. Put some car polish inside the magwell and buffed clean. Haven't had a mag stick since. YMMV
If guns are outlawed.........
 Only outlaws will have guns.

Offline puddintame

  • Sr. Member
  • ****
  • Posts: 492
Re: new CZ family member. but 1 question
« Reply #6 on: July 03, 2017, 06:50:14 PM »
No mag break on the Phantom.
   PT, I had a couple Mecgars stick a little. Put some car polish inside the magwell and buffed clean. Haven't had a mag stick since. YMMV
thanks dawg. but how did you manage to buff the inside of the magwell? as far as I can see the grip panels don't come off

Offline Stopsign32v

  • Sr. Member
  • ****
  • Posts: 311
Re: new CZ family member. but 1 question
« Reply #7 on: July 03, 2017, 08:32:29 PM »
No mag break on the Phantom.
   PT, I had a couple Mecgars stick a little. Put some car polish inside the magwell and buffed clean. Haven't had a mag stick since. YMMV
thanks dawg. but how did you manage to buff the inside of the magwell? as far as I can see the grip panels don't come off

Stick your finger in the hole...  ???

Offline DenStinett

  • Hero Member
  • *****
  • Posts: 5564
  • HALT, Who goes there?
Re: new CZ family member. but 1 question
« Reply #8 on: July 03, 2017, 08:37:57 PM »
Sized to fit the page




Nice little family you have there
So tell me again how Trump will be worse then the last 8 years !

Offline puddintame

  • Sr. Member
  • ****
  • Posts: 492
Re: new CZ family member. but 1 question
« Reply #9 on: July 03, 2017, 08:55:46 PM »
thanks den 8)

Offline 1SOW

  • Hero Member
  • *****
  • Posts: 13917
  • GO GREEN - Recycle 9MM
Re: new CZ family member. but 1 question
« Reply #10 on: July 03, 2017, 10:17:47 PM »
No mag break on the Phantom.
   PT, I had a couple Mecgars stick a little. Put some car polish inside the magwell and buffed clean. Haven't had a mag stick since. YMMV

YUP!!!  Same all the pistols:,  " Slippery is good".☺

Offline MattStainless

  • Newbie
  • *
  • Posts: 22
Re: new CZ family member. but 1 question
« Reply #11 on: July 03, 2017, 11:01:46 PM »
Off topic, but what is that finish on the 75bd?

I like the look

Offline puddintame

  • Sr. Member
  • ****
  • Posts: 492
Re: new CZ family member. but 1 question
« Reply #12 on: July 03, 2017, 11:19:10 PM »
Off topic, but what is that finish on the 75bd?

I like the look
bought both the pcr and bd from a forum member. If I remember correctly, its titanium. of all three, its the smoothest of all. but the pcr is a very close 2nd

Offline cntrydawwwg

  • Hero Member
  • *****
  • Posts: 4214
Re: new CZ family member. but 1 question
« Reply #13 on: July 04, 2017, 12:04:15 AM »
No mag break on the Phantom.
   PT, I had a couple Mecgars stick a little. Put some car polish inside the magwell and buffed clean. Haven't had a mag stick since. YMMV
thanks dawg. but how did you manage to buff the inside of the magwell? as far as I can see the grip panels don't come off

Stick your finger in the hole...  ???
   Lol. Pretty much, can't remember what I used, but wrapped a rag around a rod and used it to reach all the way through. Had the slide off also.
If guns are outlawed.........
 Only outlaws will have guns.

 

anything