HB Industries P10 trigger

[earlan357]

I just put mine it.
The trigger feels nice, but my trigger doesn't reset on its own. I double checked that I reassembled it properly.

Has anyone else run into this issue?

Does it stay completely to the rear when the slide goes forward?

Yes. I can reset it myself, but there's some resistance.

My 2nd trigger is doing it too.  I think I figured out the problem.  Will try a fix and post a video tonight.

[j@s0n]

When I first reassembled mine I had the "dingus" outside the frame before putting the pin back through that holds the trigger assembly in place, different symptom (wouldn't move at all) but you might check that.

150 rounds through mine last night, no issues and man is that reset short 

What's the dingus?

[dwhitehorne]

My trigger wouldn't reliably reset with a Glock striker spring I had in it. I put the 3.5 HBI spring in and all was fine. I've run every Speer, Lawman, Remington, Federal and Winchester ammo through my P10C with the HBI trigger and the 3.5 spring with no malfunctions/light primer strikes.  David

[seaswol]

I just put mine it.
The trigger feels nice, but my trigger doesn't reset on its own. I double checked that I reassembled it properly.

Has anyone else run into this issue?

Does it stay completely to the rear when the slide goes forward?

Yes. I can reset it myself, but there's some resistance.

My 2nd trigger is doing it too.  I think I figured out the problem.  Will try a fix and post a video tonight.

Mine is doing the same but after I sling shot the slide the trigger resets to normal.  If I ride the slide, it does not reset.  I am concerned that a spring leg may be out of place.

[seaswol]

I just put mine it.
The trigger feels nice, but my trigger doesn't reset on its own. I double checked that I reassembled it properly.

Has anyone else run into this issue?

Does it stay completely to the rear when the slide goes forward?

Yes. I can reset it myself, but there's some resistance.

My 2nd trigger is doing it too.  I think I figured out the problem.  Will try a fix and post a video tonight.

Mine is doing the same but after I sling shot the slide the trigger resets to normal.  If I ride the slide, it does not reset.  I am concerned that a spring leg may be out of place.

[nickshawn]

When I first reassembled mine I had the "dingus" outside the frame before putting the pin back through that holds the trigger assembly in place, different symptom (wouldn't move at all) but you might check that.

150 rounds through mine last night, no issues and man is that reset short 

What's the dingus?

Technical name for the trigger safety... 

[earlan357]

I just put mine it.
The trigger feels nice, but my trigger doesn't reset on its own. I double checked that I reassembled it properly.

Has anyone else run into this issue?

Does it stay completely to the rear when the slide goes forward?

Yes. I can reset it myself, but there's some resistance.

My 2nd trigger is doing it too.  I think I figured out the problem.  Will try a fix and post a video tonight.

Mine is doing the same but after I sling shot the slide the trigger resets to normal.  If I ride the slide, it does not reset.  I am concerned that a spring leg may be out of place.

I figured out the problem.  The front of the trigger bar is hitting the bottom corner of the front rail/locking block.  It turns out the factory trigger on my FDE P-10 has been doing this but not enough to really notice.  My trigger bar and locking block have gouges where it's been rubbing for over 1,400 rounds!  Video below.

[earlan357]

Also, this newer batch of triggers is not bead blasted inside the trigger notch for the "dingus".  It's smooth now, and the "roughness" when pressing the trigger safety blade is gone. 

[seaswol]

Earlan357, thank you so much for the solution and the video.  I can now can see the same problem on my pistol.  This should be a sticky sponsored by HBI.

[Toby196]

Another great fix, earlan357.  I'll most likely do this preemptively when I'm installing my new trigger, just to make sure it doesn't become an issue.  Thanks a lot.

[dwhitehorne]

Thanks for making that video.  I pulled my pistol apart this morning and stoned both of the corners.  Inside looked real close while in the gun but didn't seem to be giving me an issue.  Once I pulled it apart I could see a silver wear mark like yours from making contact at some point.  David

[MissionaryMike]

This is a very helpful thread.  I'm about to pick up a HBI trigger via CZC. 

Just curious ? what's a "dingus"?

[earlan357]

This is a very helpful thread.  I'm about to pick up a HBI trigger via CZC. 

Just curious ? what's a "dingus"?

Nickname for a trigger safety. 

[armoredman]

We're kinda informal around here.

[s0nspark]

Not to be confused with...



The trigger master!!

;-)