Author Topic: RDS Optic Plate cut  (Read 689 times)

0 Members and 1 Guest are viewing this topic.

Offline Stuart

  • Hero Member
  • *****
  • Posts: 8390
RDS Optic Plate cut
« on: September 26, 2017, 06:07:15 PM »
New optic plate cut for SP01 Shadow and 75 Shadow slides.
Offer low mounting, interchangeable plate and Rear sight plate ( Coming Soon)
Slide needs to be milled for the cut and then you have choice of plates. One plate included with cut.




Offline Smitty79

  • Hero Member
  • *****
  • Posts: 1120
  • So many guns, so little time
Re: RDS Optic Plate cut
« Reply #1 on: September 26, 2017, 10:09:35 PM »
I was in Phoenix on business today.   I had an hour to kill so I went to CZC.   I met Angus and Stuart and ordered one on of these for my Shadows.  Good times.
Don't mistake my high post count for knowledge or wisdom.   I just like hearing myself type.

Offline SI_Pop

  • Jr. Member
  • **
  • Posts: 53
Re: RDS Optic Plate cut
« Reply #2 on: September 27, 2017, 04:24:50 PM »
That looks very nice! How much will it cost to have the slide cut? Also, how much for additional plates?
1) Cajunized CZ 75 Pre B
2) Soon to be Cajunized SP-01c
3) SP-01 Shadow

Offline Deetroit

  • Newbie
  • *
  • Posts: 39
Re: RDS Optic Plate cut
« Reply #3 on: September 28, 2017, 04:23:47 PM »
I have a P10C slide I'd like to have milled.  I'm not sure which optic I'll use, either a Venom I have or an RMR I'd buy.  Therefore I like the idea of this milling setup so one could change optics by buying the corresponding plate.  How much height is added by the use of the interchangeable plates?  Of course I'd want the optic as low as possible.  I'd like to hear from some happy customers to help me with my decision.  Is there a milling option that allows one to use different optics WITHOUT using base plates?

Also, what is the rear sight plate that is coming soon?
« Last Edit: September 28, 2017, 09:07:48 PM by Deetroit »

Offline Stuart

  • Hero Member
  • *****
  • Posts: 8390
Re: RDS Optic Plate cut
« Reply #4 on: November 05, 2017, 12:07:36 PM »
SP01 Shadow with the rear sight plate.


RMR on an SP01 Shadow using the RDS plate.


Offline MissionaryMike

  • Full Member
  • ***
  • Posts: 146
Re: RDS Optic Plate cut
« Reply #5 on: November 11, 2017, 10:38:36 AM »
This is a really good idea!
"We think the 'X' is a sweet pistol, but like most CZ's, there is going to be some fine tuning to Americanize it."  -Schmeky a.k.a. CGW a.k.a. David

CZ Shadow 2 (9mm)(Cajun Seasoning)
CZ P-09 FDE (9mm)(Cajunized) (FOR SALE)
CZ P-10 C FDE (9mm)(...)

Offline smashworth

  • Newbie
  • *
  • Posts: 31
Re: RDS Optic Plate cut
« Reply #6 on: November 14, 2017, 09:32:20 AM »
I have a Sp-01. will this set up work for it....I like having the ability to switch from sights to red dot

Offline MissionaryMike

  • Full Member
  • ***
  • Posts: 146
Re: RDS Optic Plate cut
« Reply #7 on: November 14, 2017, 08:39:26 PM »
What about the Shadow 2 or P-01/PCR?
"We think the 'X' is a sweet pistol, but like most CZ's, there is going to be some fine tuning to Americanize it."  -Schmeky a.k.a. CGW a.k.a. David

CZ Shadow 2 (9mm)(Cajun Seasoning)
CZ P-09 FDE (9mm)(Cajunized) (FOR SALE)
CZ P-10 C FDE (9mm)(...)

 

anything